Summer Special Limited Time 65% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: exc65

Which action implements physical access control as part of the security program of an organization?

A.

configuring a password for the console port

B.

backing up syslogs at a remote location

C.

configuring enable passwords on network devices

D.

setting up IP cameras to monitor key infrastructure

Which protocol is used for secure remote CLI access?

A.

HTTPS

B.

HTTP

C.

Telnet

D.

SSH

What is a function of an endpoint on a network?

A.

forwards traffic between VLANs on a network

B.

connects server and client devices to a network

C.

allows users to record data and transmit to a tile server

D.

provides wireless services to users in a building

Refer to the exhibit.

Which two commands when used together create port channel 10? (Choose two.)

A.

int range g0/0-1

channel-group 10 mode active

B.

int range g0/0-1 chanm.l-group 10 mode desirable

C.

int range g0/0-1

channel-group 10 mode passive

D.

int range g0/0-1 channel-group 10 mode auto

E.

int range g0/0-1 channel-group 10 mode on

What is one reason to implement LAG on a Cisco WLC?

A.

to increase security and encrypt management frames

B.

to provide link redundancy and load balancing

C.

to allow for stateful and link-state failover

D.

to enable connected switch ports to failover and use different VLANs

Drag and drop the descriptions of AAA services from the left onto the corresponding services on the right.

Refer to the exhibit.

Which plan must be Implemented to ensure optimal QoS marking practices on this network?

A.

As traffic traverses MLS1 remark the traffic, but trust all markings at the access layer.

B.

Trust the IP phone markings on SW1 and mark traffic entering SW2 at SW2.

C.

Remark traffic as it traverses R1 and trust all markings at the access layer.

D.

As traffic enters from the access layer on SW1 and SW2. trust all traffic markings.

Which WLC management connection type is vulnerable to man-in-the-middle attacks?

A.

SSH

B.

HTTPS

C.

Telnet

D.

console

A Cisco engineer must configure a single switch interface to meet these requirements

• accept untagged frames and place them in VLAN 20

• accept tagged frames in VLAN 30 when CDP detects a Cisco IP phone

Which command set must the engineer apply?

A)

B)

C)

D)

A.

Option A

B.

Option B

C.

Option C

D.

Option D

Refer to the exhibit.

What is a reason for poor performance on the network interface?

A.

The interface is receiving excessive broadcast traffic.

B.

The cable connection between the two devices is faulty.

C.

The interface is operating at a different speed than the connected device.

D.

The bandwidth setting of the interface is misconfigured

What causes a port to be placed in the err-disabled state?

A.

nothing plugged into the port

B.

link flapping

C.

shutdown command issued on the port

D.

latency

Refer to the exhibit.

Users need to connect to the wireless network with IEEE 802. 11r-compatible devices. The connection must be maintained as users travel between floors or to other areas in the building What must be the configuration of the connection?

A.

Select the WPA Policy option with the CCKM option.

B.

Disable AES encryption.

C.

Enable Fast Transition and select the FT 802.1x option.

D.

Enable Fast Transition and select the FT PSK option.

What provides centralized control of authentication and roaming In an enterprise network?

A.

a lightweight access point

B.

a firewall

C.

a wireless LAN controller

D.

a LAN switch

Which interface mode must be configured to connect the lightweight APs in a centralized architecture?

A.

WLAN dynamic

B.

management

C.

trunk

D.

access

A Cisco engineer is configuring a factory-default router with these three passwords:

• The user EXEC password for console access is p4ssw0rd1

• The user EXEC password for Telnet access is s3cr3t2

• The password for privileged EXEC mode is pnv4t3p4ss Which command sequence must the engineer configured

A)

B)

C)

D)

A.

Option A

B.

Option B

C.

Option C

D.

Option D

Refer to the exhibit.

An engineer built a new L2 LACP EtherChannel between SW1 and SW2 and executed these show commands to verify the work. Which additional task allows the two switches to establish an LACP port channel?

A.

Change the channel-group mode on SW2 to auto

B.

Change the channel-group mode on SW1 to desirable.

C.

Configure the interface port-channel 1 command on both switches.

D.

Change the channel-group mode on SW1 to active or passive.

Which Layer 2 switch function encapsulates packets for different VLANs so that the packets traverse the same port and maintain traffic separation between the VLANs?

A.

VLAN numbering

B.

VLAN DSCP

C.

VLAN tagging

D.

VLAN marking

What is a requirement for nonoverlapping Wi-Fi channels?

A.

different security settings

B.

discontinuous frequency ranges

C.

different transmission speeds

D.

unique SSIDs

What is a function of Opportunistic Wireless Encryption in an environment?

A.

offer compression

B.

increase security by using a WEP connection

C.

provide authentication

D.

protect traffic on open networks

Refer to the exhibit.

Users on existing VLAN 100 can reach sites on the Internet. Which action must the administrator take to establish connectivity to the Internet for users in VLAN 200?

A.

Define a NAT pool on the router.

B.

Configure static NAT translations for VLAN 200.

C.

Configure the ip nat outside command on another interface for VLAN 200.

D.

Update the NAT INSIDF RANGFS ACL