Refer to the exhibit.
The DHCP server and clients are connected to the same switch. What is the next step to complete the DHCP configuration to allow clients on VLAN 1 to receive addresses from the DHCP server?
A network engineer must configure two new subnets using the address block 10 70 128 0/19 to meet these requirements:
• The first subnet must support 24 hosts
• The second subnet must support 472 hosts
• Both subnets must use the longest subnet mask possible from the address block
Which two configurations must be used to configure the new subnets and meet a requirement to use the first available address in each subnet for the router interfaces? (Choose two )
Drag and drop the characteristics of networking from the left onto the networking types on the right.
Refer to the exhibit.
Which two commands when used together create port channel 10? (Choose two.)
What is one reason to implement LAG on a Cisco WLC?
Refer to the exhibit.
Which command configures OSPF on the point-to-point link between routers R1 and R2?
A Cisco engineer must configure a single switch interface to meet these requirements
• accept untagged frames and place them in VLAN 20
• accept tagged frames in VLAN 30 when CDP detects a Cisco IP phone
Which command set must the engineer apply?
A)
B)
C)
D)
Refer to the exhibit.
Which route must be configured on R1 so that OSPF routing is used when OSPF is up. but the server is still reachable when OSPF goes down?
Which QoS traffic handling technique retains excess packets in a queue and reschedules these packets for later transmission when the configured maximum bandwidth has been surpassed?
A network administrator is setting up a new IPv6 network using the 64-bit address 2001 0EB8 00C1 2200:0001 0000 0000 0331/64 To simplify the configuration the administrator has decided to compress the address Which IP address must the administrator configure?
What is the difference between IPv6 unicast and anycast addressing?
Refer to the exhibit.
An engineer is configuring an EtherChannel using LACP between Switches 1 and 2 Which configuration must be applied so that only Switch 1 sends LACP initiation packets?
Refer to the exhibit.
The link between PC1 and the switch is up. but it is performing poorly. Which interface condition is causing the performance problem?
What is a requirement when configuring or removing LAG on a WLC?
Refer to the exhibit.
Which next-hop IP address does Routed use for packets destined to host 10 10.13.158?
Drag and drop the facts about wireless architectures from the left onto the types of access point on the right. Not all options are used.
Refer to the exhibit.
Routers R1 and R3 have the default configuration The router R2 priority is set to 99 Which commands on R3 configure it as the DR in the 10.0 4.0/24 network?
Which QoS per-hop behavior changes the value of the ToS field in the IPv4 packet header?
Refer to the exhibit.
An engineer has started to configure replacement switch SW1. To verify part of the configuration, the engineer issued the commands as shown and noticed that the entry for PC2 is missing. Which change must be applied to SW1 so that PC1 and PC2 communicate normally?
A)
B)
C)
D)
What is a function of an endpoint on a network?
Refer to the exhibit.
The router has been configured with a supernet to accommodate the requirement for 380 users on a subnet The requirement already considers 30% future growth. Which configuration verifies the IP subnet on router R4?
A)
B)
C)
D)
A Cisco engineer is configuring a factory-default router with these three passwords:
• The user EXEC password for console access is p4ssw0rd1
• The user EXEC password for Telnet access is s3cr3t2
• The password for privileged EXEC mode is pnv4t3p4ss Which command sequence must the engineer configured
A)
B)
C)
D)
What provides centralized control of authentication and roaming In an enterprise network?
An engineer must configure R1 for a new user account. The account must meet these requirements:
* It must be configured in the local database.
* The username is engineer.
* It must use the strongest password configurable. Which command must the engineer configure on the router?
Refer to the exhibit.
Which action must be taken to ensure that router A is elected as the DR for OSPF area 0?
Which two network actions occur within the data plane? (Choose two.)
Refer to the exhibit.
Which plan must be Implemented to ensure optimal QoS marking practices on this network?
Which field within the access-request packet is encrypted by RADIUS?
What is a requirement for nonoverlapping Wi-Fi channels?
Which action implements physical access control as part of the security program of an organization?
Refer to the exhibit.
A company is configuring a failover plan and must implement the default routes in such a way that a floating static route will assume traffic forwarding when the primary link goes down. Which primary route configuration must be used?
Refer to the exhibit.
All traffic enters the CPE router from interface Serial0/3 with an IP address of 192 168 50 1 Web traffic from the WAN is destined for a LAN network where servers are load-balanced An IP packet with a destination address of the HTTP virtual IP of 192 1681 250 must be forwarded Which routing table entry does the router use?
An engineer is configuring remote access to a router from IP subnet 10.139.58.0/28. The domain name, crypto keys, and SSH have been configured. Which configuration enables the traffic on the destination router?
A)
B)
C)
D)
Refer to the exhibit.
Web traffic is coming in from the WAN interface. Which route takes precedence when the router is processing traffic destined for the LAN network at 10 0.10.0/24?
Refer to the exhibit.
Which two commands must be added to update the configuration of router R1 so that it accepts only encrypted connections? (Choose two )
Refer to the exhibit.
Which configuration enables DHCP addressing for hosts connected to interface FastEthernetO/1 on router R4?
Which PoE mode enables powered-device detection and guarantees power when the device is detected?
What is the function of the controller in a software-defined network?
Refer to the exhibit.
R1 learns all routes via OSPF Which command configures a backup static route on R1 to reach the 192 168.20.0/24 network via R3?
Which value is the unique identifier that an access point uses to establish and maintain wireless connectivity to wireless network devices?
A new DHCP server has been deployed in a corporate environment with lease time set to eight hours. Which CMD command on a Windows-based device allows the engineer to verify the DHCP lease expiration?
Refer to the exhibit.
What is occurring on this switch?
Why does an administrator choose to implement a remote access IPsec VPN?
Refer to the exhibit.
A static route must be configured on R14 to forward traffic for the 172 21 34 0/25 network that resides on R86 Which command must be used to fulfill the request?
Which interface mode must be configured to connect the lightweight APs in a centralized architecture?
A network engineer is configuring a switch so that it is remotely reachable via SSH. The engineer has already configured the host name on the router. Which additional command must the engineer configure before entering the command to generate the RSA key?
Drag and drop the characteristic from the left onto the IPv6 address type on the right.
How does MAC learning function?
What is a characteristic of private IPv4 addressing?
Which feature of Digest Authentication prevents credentials from being sent in plaintext?
