Free Practice Questions for Huawei H35-580_V2.0 Exam

In order to achieve ideal coverage, there should be a clearance zone around an antenna of at least d, where d is the Fraunhofer or Rayleigh distance at which the near/far-field transition zone exists 17. This distance depends on the largest dimension of the antenna, D, and the operating wavelength, \uF06C. Ideally, D should be at least a half of a wavelength, which gives a minimum clearance zone of a half-wavelength. For example, at 2.4 GHz, the wavelength is about 0.125 m, so the minimum clearance zone is about 0.0625 m. However, in practical situations, this clearance zone is often compromised and the effects must be determined through simulation or empirical measurement 18. A general guideline is to have a clearance zone of 5-10 m around an antenna to avoid significant degradation of performance 19. Therefore, the best answer is C.

According to the HCIA-5G V2.0 Exam Outline, SS-RSRP is the reference signal received power of the synchronization signal block (SSB) in NR systems. It can be used for measurement evaluation in idle mode during coverage problem analysis, which corresponds to option D. OPMI is an indicator of uplink interference power measurement, CSI-RSRP is the reference signal received power of the channel state information reference signal (CSI-RS), and SRS is the sounding reference signal. These indicators are used for measurement evaluation in connected mode, not idle mode, which correspond to options A, B, and C.

According to the Uplink Power Control, PDCCH is the channel that is used to send uplink power control commands, also known as TPC commands. These commands indicate how much power should be increased or decreased by the UE for PUSCH or PUCCH transmissions.

According to the HCIA-5G V2.0 Exam Outline, the uplink maximum MIMO layers for 2T4R UEs is 2, which corresponds to option B.

According to the 5G-NR (EN-DC) Bearer Concept, in MR-DC (Multi-Radio Dual Connectivity) architecture, data split on a base station can be affected by the following factors:

PDCP layer buffer: The PDCP layer buffer stores user plane data before sending it to lower layers. The buffer size and occupancy can affect how data is split between LTE and NR bearers.

X2 latency: The X2 latency is the delay between LTE and NR base stations over the X2 interface. The X2 latency can affect how data is split between LTE and NR bearers by causing reordering or duplication of packets.

Air interface latency: The air interface latency is the delay between base stations and user equipment over the air interface. The air interface latency can affect how data is split between LTE and NR bearers by causing reordering or duplication of packets.

The RLC layer buffer does not affect data split on a base station because it is located below the PDCP layer where data split occurs.

Massive MIMO is a technology that uses a large number of antennas at the base station to serve multiple users simultaneously, thereby increasing the spectral efficiency and capacity of the wireless system 1. Massive MIMO is especially suitable for application scenarios where there is high user density and high traffic demand, such as large venues, high-rise buildings, and densely populated urban areas 2. Suburban areas with light traffic do not have such high requirements for spectral efficiency and capacity, and therefore are not a typical application scenario of massive MIMO.

According to the Huawei 5G Base Station Product Description, the following boards support CPU usage query:

UPEU (Universal Power and Environment Interface Unit): It provides power supply and environment monitoring functions for other boards in a subrack. It supports CPU usage query through commands or web pages.

UMPT (Universal Main Processing and Transmission Unit): It provides main processing and transmission functions for a subrack. It supports CPU usage query through commands or web pages.

UBBP (Universal Baseband Processing Unit): It provides baseband processing functions for a subrack. It supports CPU usage query through commands or web pages.

The FAN (Fan Unit) does not support CPU usage query because it does not have a CPU.

According to the Blind handover or blind redirection method and system, A3 is the event that is used by the gNodeB to trigger a blind redirection procedure. A3 is defined as “neighbour becomes offset better than serving” in 3GPP TS 38.331. When the gNodeB detects that the UE’s signal quality on a neighbouring cell is better than that on the serving cell by a certain offset, it can initiate a blind redirection procedure to switch the UE to the neighbouring cell without requiring measurement reports from the UE.