Free Practice Questions for HP HPE7-V01 Exam

The correct answer is A because Scality RING is positioned by HPE as a scale-out object and file storage solution built on qualified HPE server platforms, including HPE Alletra Storage Server models. For a customer planning approximately 750 TB of usable software-defined storage, the design focus is the validated HPE server configuration, drive type, usable-capacity target, and Scality license sizing. HPE documentation describes the Scality RING solution as consisting of HPE server systems, Scality license and maintenance, and installation services, with licensing based on unique usable data capacity. The minimum RING configuration is not 1000 TB; HPE references a lower starting usable-capacity threshold, so option B is incorrect. Option D is also incorrect because Scality solutions and licenses are explicitly available through HPE solution packaging. Option C is not the best design statement for this customer use case because the key technical validation is platform support and capacity alignment, not a generic claim about lower-cost licensing. This maps directly to the course topic covering scale-out unstructured data platforms, including Scality, Qumulo, Cohesity, and related HPE storage-server designs.

The correct answer is D. The ARP output indicates a design where gateway behavior and MAC addressing are being virtualized across switching infrastructure. In ArubaOS-CX environments, Virtual Switching Extension is the high-availability architecture that allows two independent switches to operate as an active-active pair while preserving resilient gateway and forwarding behavior. Aruba VSX active gateway specifically configures virtual IP and virtual MAC behavior for VLAN interfaces, which is the relevant design consideration when refreshing switches that currently provide redundant first-hop gateway behavior. Option A is incorrect because VSF stacking is primarily a stacking technology for supported access switching use cases; it is not the correct assumption for this data-center or aggregation-style gateway behavior. Option B is not directly proven by the ARP output; overlay networking would require VXLAN/EVPN or similar evidence. Option C is unrelated because IGMP snooping is multicast optimization and is not mandatory based only on ARP entries. The upgrade discussion must preserve VSX/active-gateway behavior if the customer depends on that design. Reference/topics: ArubaOS-CX, VSX, active gateway, architecture comparison during network refresh.

The correct answer is A because HPE Synergy can use a master/satellite interconnect design in which a smaller number of Virtual Connect modules provide the primary network intelligence, while satellite interconnect link modules extend connectivity across additional frames. This reduces the number of full Virtual Connect modules required in a multi-frame configuration, lowering hardware cost while still supporting scalable connectivity for the compute estate. In this proposal, the presence of two Virtual Connect SE 100Gb F32 modules and multiple 50Gb interconnect link modules reflects that design model. Option B describes scalability in general terms, but it does not directly identify the business and financial benefit. Option C is not the primary value proposition and does not explain the economics of the proposed topology. Option D is the opposite of the intended Synergy value: the architecture is designed to reduce, not increase, the number of expensive fabric modules in larger configurations. The course expects candidates to connect technical architecture choices to business outcomes, especially when presenting the financial impact of replacing legacy BladeSystem infrastructure with composable HPE Synergy infrastructure.

The correct answer is A. The switch output clearly identifies the VTEP origin as “static,” and the VNI is mapped to VLAN 150 with routing disabled. In ArubaOS-CX static VXLAN, the administrator manually configures the VXLAN interface, source IP address, VNI, and peer VTEP. Aruba documentation for static VXLAN states that the peer VTEP IP address is explicitly defined with the vtep-peer command. Option B describes EVPN-VXLAN behavior, where BGP EVPN is used as the control plane to advertise MAC/IP and VTEP reachability dynamically. That is not what the output shows; the displayed origin is static. Option C is unsupported by the exhibit because no license state or scale limit is shown. Option D is incorrect because VXLAN interoperability depends on protocol support, configuration, MTU, underlay reachability, and feature compatibility, not on both sites using the exact same CX switch model. Reference/topics: ArubaOS-CX VXLAN, static VTEP configuration, VNI-to-VLAN mapping, underlay/overlay validation.

The correct answer is A. Omnissa Unified Access Gateway is the edge access component used with Horizon to provide secure remote access from an external network to internal Horizon desktops and applications. It is commonly positioned in a DMZ and avoids exposing internal Horizon infrastructure directly to external users. Omnissa documentation describes Unified Access Gateway as enabling secure remote access from external networks to Workspace ONE and Horizon resources, and Horizon installation guidance describes it as the default gateway for secure access to remote desktops and applications from outside the corporate firewall. Option B is incorrect because Horizon support is not limited to a minimum of more than 720 desktops, nor is it only supported through a generic HPE Compute qualification. Option C is technically wrong because Horizon can use supported VMware datastore types such as VMFS, NFS, and vVols depending on the validated design. Option D is also wrong because GPU resources are required only for graphics-accelerated use cases, not for every Horizon cluster. Reference/topics: workload requirement analysis, VDI architecture, HPE compute platform positioning, secure access design.

The correct answer is B because HPE Alletra Storage MP B10000 supports VMware-oriented high-availability designs using Peer Persistence / Active Peer Persistence patterns. HPE documentation provides VMware ESXi host connectivity guidance for Alletra Storage MP B10000 and also describes VMware Metro Storage Cluster configurations with Active Peer Persistence. That is the correct platform positioning for protecting VMware workloads that require storage-level availability across sites. Option A is incorrect because Alletra 6000 Peer Persistence is based on NimbleOS synchronous replication behavior and is not positioned as an “Active Peer Persistence wizard with one-to-many topology.” Option C is also incorrect because Active Peer Persistence is a high-availability replication design, not a one-to-many replication topology. One-to-many replication is a different replication pattern and should not be conflated with Peer Persistence. Option D is incorrect because “Active Peer Persistence” is associated with Alletra Storage MP B10000 / Primera / Alletra 9000-class architecture rather than Alletra 6000’s classic Peer Persistence model. Reference/topics: HPE Alletra Storage MP B10000, VMware ESXi integration, Active Peer Persistence, storage HA design.

The correct answer is D because existing HPE SimpliVity systems can be brought under HPE GreenLake / Data Services Cloud Console management by using the Data Services Connector. The connector is deployed as a virtual machine, registered with HPE GreenLake, and used to enable or import supported HPE SimpliVity systems into the cloud-managed PCBE operating model. This fits the customer’s transition scenario exactly: production is moving to the new Gen11 PCBE environment, but the older Gen10 SimpliVity cluster remains useful for test and development. Option A is incorrect because the new PCBE platform should not be downgraded to preserve legacy-style management. Option B is also wrong because the existing cluster does not need to be redeployed as a brand-new PCBE installation. Option C is directionally close but imprecise: the management plane is HPE GreenLake / DSCC using Data Services Connector, not the new PCBE system “managing” the old platform directly. Reference/topics: HPE GreenLake, Private Cloud Business Edition, Data Services Connector, SimpliVity onboarding and lifecycle management.

The correct answer is B. The controlling requirement is the 95 km / 60 mile inter-data-center Fibre Channel distance. Standard Fibre Channel fabrics have native distance limits, and long-distance SAN designs require the correct licensing and buffer-credit behavior to maintain stable inter-switch link operation. HPE SAN design guidance states that B-series switches provide extended fabric support up to 10 km by default, but for distances greater than 10 km an Extended Fabrics license is required. Therefore, the configuration must include or modify the Fibre Channel software licensing to support the required long-distance fabric behavior. Option A is not the architectural issue; optics can be changed, but the long-distance fabric still needs the correct licensing and configuration. Option C is misleading because port form factor compatibility alone does not satisfy 95 km operation. Option D is too specific to port numbering and does not solve the distance requirement. The quote must be validated for both physical optics and the SAN feature license that enables extended-distance behavior. Reference/topics: HPE B-series Fibre Channel switching, Extended Fabric, inter-data-center SAN design, proposal validation.

The correct answer is A because HPE OneView for VMware vCenter provides VMware administrators with integrated HPE infrastructure management from within vCenter and supports deployment workflows for ESXi hosts on supported HPE platforms such as HPE Synergy and HPE ProLiant. In this scenario, the customer already has a Synergy, 3PAR, and VMware environment and wants to extend it for additional virtual machines running database workloads. Adding ESXi hosts through the HPE OneView for VMware vCenter integration is a valid upgrade path because it aligns server provisioning and VMware lifecycle operations with the existing management model. Option B is incorrect because it confuses infrastructure automation with the specific HPE OneView for VMware vCenter ESXi deployment function. Option C is false because HPE 3PAR has long been supported in VMware environments and can be part of Synergy-based infrastructure. Option D is imprecise: HPE OneView composes and manages infrastructure; it is not primarily a rapid VM deployment tool. The course covers database workload architectures, Synergy, HPE storage, VMware integration, and the use of HPE tools for validated traditional solution design.