Spring Sale Special - Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: sntaclus

A mid-size service provider uses L2VPN as its standard for connectivity between offices. A small company wants the service provider to connect the company's two sites across the service provider core. To meet service requirements, the service provider must extend the Layer 2 domain between the company's two locations.

Which configuration must the engineer apply to implement an attachment circuit between the two sites using a VLAN tag of 12?

A.

interface TenGigE0/0/0/1.0 12transport

 encapsulation dot1q 12

B.

interface TenGigE0/0/0/1.0 12transport

 encapsulation dot1q 12

 rewrite ingress tag push dot1q 21 symmetric

C.

interface TenGigE0/0/0/1.0 12transport

 encapsulation dot1q 12

 rewrite ingress tag pop 13

D.

interface TenGigE0/0/0/1.0 12transport

 encapsulation dot1q 12

 rewrite ingress tag translate 1-to-1 dot1q 2

A router is configured to perform MPLS LDP graceful restart.

Which three steps are included when the RP sends an LDP initialization to a neighbor to establish an LDP session? (Choose three)

A.

Reconnect Timeout field

B.

Learn from Neighbor (N) flag, set to 1

C.

Graceful restart capability in OPEN message

D.

Recovery Time field

E.

Learn from Network (L.) flage, set to 1

F.

Type-9 LSA

What happens when a segment-routing TE tunnel loses the link and there is no secondary path in place?

A.

The headend router generates a new path to the tail-end router using bandwidth to determine the best path.

B.

The tail-end router sends an alert to the syslog server that the tunnel and the secondary route are inaccessible.

C.

The headend router starts the invalidation timer to bring the tunnel down.

D.

The headend and tail-end routers revalidate SID hops to determine the proper label stack to reroute the traffic.

Refer to the exhibit. In the service provider network, routers PE1, PE2, and PE4 have access to the internet and provide access to customer networks. Router PE3 is used for access to other customer systems. In accordance with a new SLA, an engineer is updating settings on this network so that router CE1 accesses the internet via PE1 instead of PE2. Which two tasks must the engineer perform to complete the process? (Choose two.)

A.

On PE1, configure the internet VRF with import route target 102:102.

B.

On PE1 and PE4, configure the internet VRF with import route targets 102:102 and 104:104.

C.

On PE2, configure the internet VRF with import route target 102:102.

D.

On PE2 and PE3, configure the internet VRF with import route target 101:101.

E.

On PE2, configure the CE1 VRF with import route target 101:101.

Refer to the exhibit.

Routers R2 and R3 are Level 1/Level 2 IS-IS routers that redistribute 198 18.x.x/24 prefixes to routers R5 and R6 In the Level 1 area R2 Is to be the preferred router for all redistributed prefixes in the Level 1 area. Which configuration sets this preference?

A.

Option A

B.

Option B

C.

Option C

D.

Option D

Refer to the exhibit A user is performing QoS marking on internet traffic and sending it with IPv4 and IPv6 headers on the provider edge device PE1. IPv4 traffic is classified with DSCP 4 and IPv6 traffic is classified with DSCP 6. Which action must the engineer take to begin implementing a QoS configuration on PE1 for the IPv6 traffic?

A.

Create an access list that includes any IPv6 traffic and apply it to CM-20.

B.

Create access list IPv6-match and configure match ip dscp 4 and match ip dscp 6 in class maps CM-10 and CM-20.

C.

Configure match ip dscp 4 in class map CM-10 and match ip dscp 6 in class map CM-20.

D.

Create access list IPv6-filter and remove DSCP value 4 and 6 in class maps CM-10 and CM-20.

Which statement describes the advantage of a Multi-Layer control plane?

A.

It automatically provisions monitors, and manages traffic across Layer 0 to Layer 3

B.

It minimizes human error configuring converged networks

C.

It supports dynamic wavelength restoration in Layer 0

D.

It provides multivendor configuration capabilities for Layer 3 to Layer 1

Refer to the exhibit.

A network engineer is implementing OSPF multiarea. Which command on interface GO/1 resolves adjacency issues in the new area?

A.

ip ospf network broadcast

B.

ip ospf network point-to-point

C.

ip ospf network non-broadcast

D.

ip ospf network point-to-multipoint

Refer to the exhibit. A growing company with an increasing international presence requires a secure and scalable solution for inter-office data transfer across their geographically dispersed locations. To ensure departmental privacy, the network must enforce granular access control. BGP is running in the network, and two VRF instances with unique route distinguishers and route targets have been configured to segregate critical financial data from regular network traffic. A network engineer with an employee ID: 5086:72:617 must find a solution that allows for future network expansion while maintaining robust security and data privacy between departments. The solution must comply with the RFC 4364 standard. Which action must the engineer take to meet the requirements?

A.

Configure a GRE tunnel in AH mode between the two routers.

B.

Configure MPLS in L3VPN mode between the two routers.

C.

Configure a DMVPN connection between the two routers with Phase 2 mode enabled.

D.

Configure an IPsec VPN connection between the two routers with ESP protocol enabled.

A network operator working for a private outsourcing company with an employee id: 4261:72:778 needs to limit the malicious traffic on their network. Which configuration must the engineer use to implement URPF loose mode on the GigabitEthernet0/1 interface?

A.

router(config)# interface gigabitethernet0/1

router(config-if)# ip address 192.168.200.1 255.255.255.0

router(config-if)# ip verify unicast source reachable-via any

router(config-if)# ipv6 address 2001:DB8:1::1/96

router(config-if)# ipv6 verify unicast source reachable-via any

B.

router(config)# interface gigabitethernet0/1

router(config-if)# ip address 192.168.200.1 255.255.255.0

router(config-if)# ip verify unicast source reachable-via rx

router(config-if)# ipv6 address 2001:DB8:1::1/96

router(config-if)# ipv6 verify unicast source reachable-via rx

C.

router(config)# interface gigabitethernet0/1

router(config if)# ip address 192.168.200.1 255.255.255.0

router(config-if)# ip verify unicast source reachable-via rx

router(config-if)# ipv6 address 2001:DB8:1::1/96

router(config-if)# ipv6 verify unicast source reachable-via any

D.

router(config)# interface gigabitethernet0/1

router(config-if)# ip address 192.168.200.1 255.255.255.0

router(config-if)# ip verify unicast source reachable-via any

router(config-if)# ipv6 address 2001:DB8:1::1/96

router(config-if)# ipv6 verify unicast source reachable-via rx

Refer to the exhibit.

A network operator needs to shut down interface Gi0/0/0/2 for maintenance. What occurs to the interface states of Gi0/0/0/0 and Gi0/0/0/1?

A.

Gi0/0/0/1 and Gi0/0/0/0 become active

B.

Gi0/0/0/1 and Gi0//0/0 remains standby

C.

Gi0/0/0/0 becomes active. Gi0/00/1 remains standby

D.

Gi0/0/0/1 becomes active Gi0/0/0/0 remains standby

Refer to the exhibit. The network is configured with OSPF. A networking team just connected a streaming multicast server to router R7, and they now must enable access for users throughout the network to stream video from the server.

Which action must the team take so that users can stream video without overloading the network?

A.

Implement PIM-DM on the link between the server and R7.

B.

Implement PIM-SM on the LAN network connecting R5, R6, R3, and R4.

C.

Implement PIM-SM on all routers and connected links.

D.

Implement PIM-DM on all interfaces in the network except the LAN connection between R5, R6, R3, and R4.

Refer to the exhibit.

What reestablishes the OSPF neighbor relationship between Router 1 and Router 2?

A.

authentication is added to the configuration

B.

correct wildcard mask is used on Router 2

C.

OSPF process IDs match

D.

hello intervals match

Refer to the exhibit. A service provider is running MPLS in the core to support Layer 3 VPN. OSPF is configured to support dynamic routing, and BGP is enabled throughout the network. A network engineer is adding a new P router to the infrastructure and is connecting it to P1 and P3.

Which task must the engineer perform on the new router to allow it to participate in the Layer 3 VPN?

A.

Enable LDP sync under the OSPF routing process.

B.

Establish an LDP neighbor relationship with P1 and P3.

C.

Configure OSPF and BGP to support MPLS.

D.

Enable LDP and establish an OSPF adjacency in a new area.

What are two purposes of a data-modeling language such as YANG? (Choose two.)

A.

defining a hierarchical data scheme

B.

modeling notifications, data configuration, and data status

C.

defining a relational-model data scheme

D.

defining a semi-structured data scheme

E.

defining API calls, JSON format, and XML structure