Free Practice Questions for Nutanix NCSE-Core Exam

To determine the minimum amount of HDD capacity required for the workload after converting thick provisioned disks to thin provisioned disks, we need to consider the active working set and the typical overhead for thin provisioning.

Current Capacity:

The prospect currently has 8500GB (8.5TiB) of provisioned capacity.

Active Working Set:

The total active working set for the cluster is determined to be 1TB.

Thin Provisioning:

Thin provisioning reduces the need for physical storage because it allocates storage on-demand rather than reserving the full capacity upfront.

Nutanix typically advises planning for additional overhead to accommodate metadata, snapshots, and potential growth.

Calculation:

The rule of thumb for thin provisioning overhead is approximately 2-3 times the active working set to ensure adequate capacity for metadata and additional data growth.

Using the higher end of the multiplier (3 times):

1TB (active working set)×3=3TB1 \text{TB (active working set)} \times 3 = 3 \text{TB}1TB (active working set)×3=3TB

Conclusion:

Therefore, the minimum HDD capacity required for the workload when thin provisioning is applied would be around 3.0TiB.

References:

Nutanix Sizing Guidelines.

Nutanix Documentation on Thin Provisioning and Storage Optimization.

Document Purpose:

AReference Architectureprovides a comprehensive framework for designing, implementing, and managing a solution. It includes validated configurations, best practices, and deployment guidelines tailored to specific applications or workloads.

Suitability for Avaya IP Office Migration:

This type of document is ideal for addressing concerns about the suitability and design of using Nutanix for Avaya IP Office migration as it includes detailed technical guidance and architecture designs that ensure compatibility and performance (Nutanix Bible, Architecture Overview section)​​.

Conclusion:

Providing a Reference Architecture will address the prospect’s concerns with a detailed, validated approach for deploying Avaya IP Office on Nutanix, ensuring a reliable and efficient migration.

References:

Nutanix Reference Architecture documents

Nutanix Bible on Architecture Overview

For network switch discovery in Prism, the following settings are required:

Switch Management IP Address: This is necessary to access and manage the network switch.

AHV Host IP address: This helps in identifying the hosts connected to the network.

SNMP Community Name: This is used for SNMP protocol to monitor and manage the network devices​​​​.

Nutanix Foundation is the tool used for imaging nodes that are either bare metal or require a different hypervisor. Foundation is designed for bootstrapping the imaging and deployment of Nutanix clusters. It installs the desired version of the Acropolis Operating System (AOS) and the hypervisor of choice. By default, Nutanix nodes ship with AHV pre-installed, but Foundation can be used to re-image the nodes with a different hypervisor if required.

References:

Nutanix Bible

To verify if all network cards associated with BridgeO are being used by nodes in an AHV cluster, you need to examine the network configuration and the network interface cards (NICs) on the hosts. The following menus in the Prism interface will provide the necessary information:

Host NICs tab in Hardware menu:

This tab provides a detailed view of all NICs available on each host in the cluster.

It shows the status, speed, and configuration of each NIC, which helps determine if all network cards are active and properly associated with BridgeO.

Host view in Network menu:

The Network menu under the Host view provides insights into the network configuration for each host.

It includes information on how NICs are bridged, VLAN assignments, and overall network topology, confirming if all NICs are effectively used and contributing to the bridge.

These menus collectively ensure that the administrator can verify the network setup and utilization of all network interfaces.

References:

Nutanix Bible, Networking section detailing NIC and bridge configuration​​.

Nutanix-Community-Edition-Getting-Started, Sections on network management and host configuration​​.

In Sizer, when creating a multi-cluster scenario, the Summary Failover Capacity indicator (N+0, N+1) shows the worst resiliency level of any cluster in the scenario. This helps in identifying the weakest link in terms of failover capacity across multiple clusters. If any cluster within the scenario has a lower failover capacity, the indicator will reflect this to ensure that the overall solution can handle the identified worst-case scenario​​.

Sizer Scenario Utility:

Nutanix Sizer is a tool used to configure and size Nutanix deployments based on customer workloads and requirements.

Actions Possible with BOM (Bill of Materials):

Review Budgetary Pricing: The BOM provides detailed component and configuration costs, enabling budgetary analysis.

Review Workload Sizing Details: The Sizer generates detailed workload sizing, helping validate if the proposed configuration meets the performance needs.

Actions Not Possible:

Review Power Consumption Requirements: Sizer primarily focuses on performance and cost, not detailed power requirements.

Review Applicable Discounts: This is typically handled through sales channels and deal registrations, not directly via Sizer.

Reference HCL for Additional SKUs: The Hardware Compatibility List (HCL) lookup is beyond the scope of the immediate BOM review.

References:

Nutanix Sizer tool documentation and usage guidelines.

B. N+1:

Based on the sizing scenario and the configuration shown in the exhibit, the Failover option selected is "Standard (N+1)."

This indicates that the cluster is configured to provide N+1 resiliency, where the system can handle the failure of one node by having an additional node available to take over.

This level of resiliency is common in environments where a balance between cost and availability is required.

References:

Nutanix Sizer tool and Nutanix documentation provide detailed explanations on configuring clusters with different levels of resiliency, including N+1.

To enable prospective customers to gain hands-on experience with Nutanix without the need for support from a systems engineer or Nutanix, the following resources are available:

Test Drive:

Nutanix Test Drive provides a hands-on, guided tour of Nutanix solutions in a live environment. It allows customers to explore and interact with Nutanix features and functionalities, simulating real-world scenarios and workflows.

Community Edition (CE):

Nutanix Community Edition is a free version of Nutanix AOS that customers can deploy on their own hardware. It allows users to test and evaluate Nutanix software in a non-production environment, providing full access to Nutanix features and capabilities for learning and experimentation.

References:

Nutanix Community Edition Getting Started Guide