Free Practice Questions for iSQI CTFL_Syll_4.0 Exam

The best example of a test case for this user story should cover the acceptance criteria comprehensively. Option A addresses the critical aspects of the acceptance criteria:

Verifying the discount for the first timeslot (8 AM GMT) - ensuring it provides a 10% discount.

Verifying that changing the time slot removes the discount - ensuring the discount logic is correctly applied.

This test case effectively validates the functionality related to both the discount and the ability to change time slots, which are key parts of the user story's requirements​​.

Good testing practices that apply to all software development lifecycles include having specific test objectives for each test level that align with the phase of the software development lifecycle and the type of activities being addressed. This approach ensures that testing activities are relevant and appropriate for the specific stage of development, enhancing the effectiveness and efficiency of the testing process.

Black-box testing techniques focus ontesting the functionality of the software without knowledge of its internal workings(D). They derive test cases fromspecifications, requirements, or expected behavior.Option Adescribes exploratory testing,Bcontradicts the definition by focusing on implementation, andCincorrectly includes "implied behavior," which is not a core characteristic of black-box testing.

Maintenance testing is carried outwhenever changes are made to an existing system, including enhancements, defect fixes, and system migrations (C). It is not limited to adaptive maintenance (A) and is needed even when no defects are reported (B). Test cases are essential to validate fixes and prevent regressions (D).

Acceptance criteria8states thatthe system should charge the user on the first business day of the following month. However, thetest cycle only verified monthly payments for over a year, without confirming whether payments were processedspecifically on the first business day.

(B) is incorrectbecause the test validatedmonthly and annual payment options.

(C) is incorrectbecause not all criteria were fully validated.

(D) is incorrectbecause OTP verification (6) was tested as part of registration.

Ensuringtimely execution of payments(Criteria 8) requires additional validation.

The question is about marking the correct sentences among the given statements related to defects, failures, and mistakes. According to the ISTQB glossary, the definitions of these terms are1:

Defect: A flaw in a component or system that can cause the component or system to fail to perform its required function, e.g. an incorrect statement or data definition. A defect, if encountered during execution, may cause a failure of the component or system.

Failure: An event in which a component or system does not perform a required function within specified limits.

Mistake: A human action that produces an incorrect result.

Therefore, out of the five given statements, only two are correct, namely:

A human mistake may produce a defect: This is true, as a mistake is a source or cause of a defect, e.g. a programmer may make a mistake in writing a code statement, which results in a defect in the software component.

When a defect exists in a system it may result in a failure: This is true, as a defect is a potential or actual cause of a failure, e.g. a defect in the software component may cause the system to fail to perform a required function when the defect is encountered during execution.

The other three statements are incorrect, namely:

Defects are a result of environmental conditions and are also referred to as “Failures”: This is false, as defects are not a result of environmental conditions, but of mistakes or other factors, and defects are not the same as failures, but rather the causes of failures.

A system will totally fail to operate correctly when a failure exists in it: This is false, as a system may not necessarily fail completely or stop operating when a failure occurs, but may continue to operate with reduced functionality or performance, or with incorrect results.

Defects occur only as a result of technology changes: This is false, as defects can occur due to various reasons, not only technology changes, such as human mistakes, design flaws, requirement changes, hardware failures, etc.

A failure is an event in which a component or system does not perform a required function within specified limits1. A requirement is a condition or capability needed by a user to solve a problem or achieve an objective2. In this case, the requirement is that the diagnostics tests should execute in less than 2 seconds. Therefore, any event that violates this requirement is a failure. The only option that clearly violates this requirement is B. The diagnostic tests take too much time to execute. If the diagnostic tests take more than 2 seconds to complete, then they do not meet the specified limit and thus fail. The other options are not necessarily failures related to the specified requirement. Option A. The diagnostic tests fail to start after a system reset is a failure, but not related to the time limit. It is related to the functionality of the self-diagnostics module. Option C. The diagnostic tests that measure the speed of the memory, fail is also a failure, but not related to the time limit. It is related to the accuracy of the memory tests. Option D. The diagnostic tests fail due to incorrect implementation of the test code is also a failure, but not related to the time limit. It is related to the quality of the test code. References = ISTQB® Certified Tester Foundation Level Syllabus v4.0, Requirements Engineering Fundamentals.

The question is about selecting the correct test values for x based on equivalence partitioning. Equivalence partitioning is a software test design technique that divides the input data of a software unit into partitions of equivalent data from which test cases can be derived. In this case, the given equivalence classes are:

(x \leq -100)

(-100 < x < 100)

(100 \leq x < 1000)

(x \geq 1000)

Option D provides a value from each of these partitions:

For (x \leq -100), it gives -1000.

For (-100 < x < 100), it gives -100 and 100.

For (100 \leq x < 1000), it gives 500.

For (x \geq 1000), it gives 1500.

So, option D covers all four given equivalence classes with appropriate values.

State transition testing validatesvalid and invalid state transitionsbased on defined rules.

D is invalidbecause it transitionsfrom DIAGNOSTIC MODE directly to EMERGENCY MODE, which isnot a valid state changein most systems.

Other options follow valid sequences according tostate transition rules.

This answer is correct because product risks are risks that affect the quality of the software product, such as defects, failures, or non-compliance with requirements or standards. Project risks are risks that affect the project’s schedule, budget, resources, or scope, such as delays, cost overruns, skill gaps, or scope changes. In this case, [I] and [IV] are product risks, as they relate to the accessibility and security of the software product, which are quality attributes. [II] and [III] are project risks, as they relate to the delivery time and the test automation skills of the test team, which are project factors. References: ISTQB Glossary of Testing Terms v4.0, ISTQB Foundation Level Syllabus v4.0, Section 2.1.1.1