Free Practice Questions for CompTIA SK0-005 Exam

A synthetic full backup is a type of backup that copies changed data from a server and then combines the backups on the backup target. This way, the backup target always has a full backup of the server, without requiring a full backup to be performed over the network. A synthetic full backup reduces the network bandwidth and time required for backups, while also simplifying the restoration process1

The most likely cause of the servers displaying the wrong time is A. A firewall. A firewall is a network security device that monitors and controls incoming and outgoing network traffic based on predefined rules. A firewall can block or allow certain ports, protocols, or applications that are used for network communication.

One of the protocols that is used for time synchronization is the Network Time Protocol (NTP), which requires the use of UDP port 123 for all time synchronization1. If a firewall blocks this port, it can prevent the servers from obtaining the correct time from the time source. Therefore, the server administrator should check the firewall settings and make sure that UDP port 123 is allowed for NTP traffic.

The BIOS (Basic Input/Output System) or UEFI (Unified Extensible Firmware Interface) setup is a program that allows users to configure the hardware settings of a computer, such as the CPU, memory, disk, and boot options. The BIOS/UEFI setup can be accessed by pressing aspecific key (such as F2, F10, or Delete) during the boot process, before the operating system loads12.

One of the settings that can be changed in the BIOS/UEFI setup is the CPU hyperthreading option. Hyperthreading is a technology that enables a single physical CPU core to execute two threads or tasks simultaneously, improving the performance and efficiency of multi-threaded applications. However, some software licenses may limit the number of CPU cores or threads that can be used, and therefore require disabling hyperthreading on the server34.

To disable hyperthreading on a server, the administrator will likely need to enter the BIOS/UEFI setup and navigate to the processor options menu. There, the administrator will find a setting for Intel ® Hyperthreading Technology or Hyperthreading Function, which can be enabled or disabled. The administrator will need to disable this setting and save the changes. This will turn off hyperthreading on the server and reduce the number of logical CPUs to match the number of physical cores5.

MRU, or Most Recently Used, is a concept that refers to prioritizing a connection that had previously worked successfully. It is often used in load balancing algorithms to distribute the workload among multiple servers or paths. MRU assumes that the most recently used connection is the most likely to be available and efficient, and therefore assigns the next request to that connection. This can help reduce latency and improve performance12. The other options are incorrect because they do not refer to prioritizing a previous connection. Round robin is a concept that refers to distributing the workload equally among all available connections in a circular order12. SCP, or Secure Copy Protocol, is a concept that refers to transferring files securely between hosts using encryption3. Link aggregation is a concept that refers to combining multiple physical links into a single logical link to increase bandwidth and redundancy4.

RAID 5 is a RAID level that provides striping with parity, which means that data is distributed across all disks with one disk storing parity information for error correction. RAID 5 can tolerate one disk failure without losing data. RAID 5 provides the most storage as well as disk redundancy out of the four RAID levels given, since it only uses one disk for parity and the rest for data. For example, if four 200GB drives are used in a RAID 5 array, the total storage capacity would be 600GB (200GB x 3), while in RAID 0 it would be 800GB (200GB x 4), in RAID 1 it would be 200GB (200GB x 1), and in RAID 10 it would be 400GB (200GB x 2).References:https://en.wikipedia.org/wiki/Standard_RAID_levels#RAID_5

The cache is a temporary storage area that holds frequently accessed data or instructions for faster retrieval. The cache can improve the read times for accessing files by reducing the need to access the hard drive, which is slower than the cache memory1. Therefore, the first step the technician should take is to check if the cache is turned on for the new file server. If the cache is turned off, the technician should enable it and see if the read times improve. The other options are incorrect because they are not the first steps to take. Adding more memory, installing faster hard drives, or enabling link aggregation are possible ways to improve the performance of the file server, but they are more costly and time-consuming than checking the cache. Moreover, they may not address the root cause of the problem if the cache is turned off.

An incremental backup is a backup method that only backs up the files that have changed since the last backup, whether it was a full or an incremental backup. An incremental backup can save disk space and time, as it only copies the new or modified data. An incremental backup can also improve the RTO (Recovery Time Objective), which is the maximum acceptable time to restore data after a disaster. This is because an incremental backup can restore data faster than a full or a differential backup, as it only needs to apply the latest changes to the previous backup1.

A differential backup is a backup method that protects all the changes that have occurred since the last full backup. A differential backup copies all the files that have been added or modified since the last full backup, regardless of whether they have been backed up before or not. A differential backup does not reset the archive bit of the files, which means they will be backed up again in the next differential backup. A differentialbackup requires more storage space and time than an incremental backup, but it simplifies the restoration process, as only the last full backup and the last differential backup are needed to restore the data

RTO stands for Recovery Time Objective and it is a metric that defines the maximum acceptable amount of time that a system or service can be unavailable after a disaster or disruption. RTO is part of the business continuity planning and disaster recovery planning processes. RTO ensures a guarantee of the amount of time it will take to restore a downed service by setting a target or goal for recovery. RTO can vary depending on the criticality and priority of the service.References: https://www.comptia.org/training/resources/exam-objectives/comptia-server-sk0-005-exam-objectives (Objective 3.3)

A sniffer is a tool that captures and analyzes network traffic on a subnet or a network interface. It can help identify the source, destination, protocol, and content of the traffic and detect any anomalies or issues on the network. Verified References: [Sniffer], [Network traffic]