Free Practice Questions for Checkpoint 156-315.81 Exam

The correct command to show actual allowed connections in the state table is option B: fw tab –t connections. This command displays the contents of the "connections" table, which contains information about the active connections being tracked by the firewall.

Option A (fw tab –t StateTable) is incorrect as there is no "StateTable" table; it should be "connections."

Option C (fw tab –t connection) is also incorrect, as it should be "connections."

Option D (fw tab connections) is not the correct syntax for the command.

References: Check Point Certified Security Expert (CCSE) R81 documentation and learning resources.

To optimize drops you decide to use Priority Queues and fully enable Dynamic Dispatcher. You can enable them by using the command fw ctl multik set_mode 9. This command sets the SecureXL mode to 9, which means that Priority Queues are enabled and Dynamic Dispatcher is fully enabled. References: SecureXL Mechanism

Anti-Bot is a post-infection malware protection that detects and blocks botnet communications from infected hosts to Command & Control servers. It is different from other Threat Prevention mechanisms that prevent malware from entering the network or executing on the hosts. References: Anti-Bot Software Blade

Check Point recommends configuring Disk Space Management parameters to delete old log entries when available disk space is less than or equal to a certain threshold. In this case, the correct threshold is specified as option D: 15%.

So, when the available disk space reaches or falls below 15%, old log entries should be deleted to free up space.

Options A, B, and C do not represent the recommended threshold for deleting old log entries according to Check Point's best practices.

References: Check Point Certified Security Expert (CCSE) R81 documentation and learning resources.

The SmartEvent component that creates events is the Correlation Unit, which is responsible for correlating and analyzing security events to identify patterns and potential threats.

Option A, "Consolidation Policy," does not create events but is used to configure policies for event consolidation.

Option C, "SmartEvent Policy," is not responsible for creating events but is used to configure policies related to SmartEvent.

Option D, "SmartEvent GUI," is the graphical user interface for managing SmartEvent but does not create events itself.

References: Check Point Certified Security Expert (CCSE) R81 documentation and learning resources.

The cphaconf set_ccp multicast command is used to set the Cluster Control Protocol (CCP) to Multicast mode. This mode allows cluster members to communicate with each other using multicast packets. The other commands are either incorrect or set the CCP to Broadcast mode. References: ClusterXL Administration Guide

 The process that pulls application monitoring status is cpd. cpd is a daemon that runs on Check Point products and performs various tasks related to management communication, policy installation, license verification, logging, etc. cpd also monitors the status of other processes and applications on the system and reports it to the management server. cpd uses SNMP to collect information from various sources, such as blades, gateways, servers, etc. You can view the application monitoring status in SmartConsole by using the Gateways & Servers tab in the Logs & Monitor view. References: Check Point Processes and Daemons

The difference between an event and a log is that a log entry becomes an event when it matches any rule defined in Event Policy. A log entry is a record of a network activity that is generated by a Security Gateway or a Management Server. An event is a log entry that meets certain criteria and triggers an action or a notification. The other options are either not true or not accurate definitions of events and logs. References: Check Point R81 Logging and Monitoring Administration Guide

The Audit Log is a feature that records all the actions performed by R81 SmartConsole administrators, such as logging in, logging out, publishing, installing policy, creating objects, modifying rules, etc. You can see and search records of action done by R81 SmartConsole administrators by following these steps:

In SmartConsole, go to Logs & Monitor view.

In the left pane, select Open Audit Log View.

In the right pane, you will see a table that shows all the audit log records. You can filter, sort, group, or search the records by using the toolbar options.

You can also double-click on a record to see more details in a pop-up window. References: R81 Logging and Monitoring Administration Guide

 Dynamic Dispatcher is a feature that optimizes the performance of Security Gateways with multiple CPU cores by dynamically allocating traffic to different cores based on their load and priority. Firewall Priority Queues is a feature that prioritizes traffic based on its type and importance by assigning it to different queues with different weights and limits. To fully enable Dynamic Dispatcher with Firewall Priority Queues on a Security Gateway, you need to run the following command in Expert mode then reboot:

This command sets the multi-core mode to 9, which means that Dynamic Dispatcher is enabled with Firewall Priority Queues. The other commands are not valid or do not enable both features. References: R81 Performance Tuning Administration Guide

 Sticky Decision Function (SDF) is required to prevent asymmetric routing in an Active-Active cluster. Asymmetric routing occurs when packets from a source to a destination follow a different path than packets from the destination to the source. This can cause problems with stateful inspection and NAT. SDF ensures that packets from the same connection are handled by the same cluster member1. References: Check Point R81 ClusterXL Administration Guide

 Check Point Mobile Web Portal is a Mobile Access Application that allows a secure container on mobile devices to give users access to internal websites, file shares and emails. The Mobile Web Portal is a web-based application that can be accessed from any browser on any device. It provides a user-friendly interface to access various resources on the corporate network without requiring a VPN client or additional software installation. The Mobile Web Portal supports authentication methods such as user name and password, certificate, one-time password (OTP), etc. The Mobile Web Portal also supports security features such as encryption, data leakage prevention (DLP), threat prevention, etc. References: R81 Mobile Access Administration Guide

The Event List within the Event tab contains events generated by a query. The Event List shows the events that match the query criteria, such as time range, filter, and aggregation. The events can be sorted by different columns, such as severity, time, action, and source3. The other options are either not part of the Event tab or not related to the Event List. References: Check Point R81 Logging and Monitoring Administration Guide

The CLI command to reset the IPS (Intrusion Prevention System) pattern matcher statistics is option D: ips pmstats reset. This command will reset the statistics related to the IPS pattern matcher.

Options A, B, and C are not the correct syntax for resetting the IPS pattern matcher statistics.

References: Check Point Certified Security Expert (CCSE) R81 documentation and learning resources.

SandBlast Mobile has four components: Management Dashboard, Gateway, Behavior Risk Engine, and On-Device Network Protection. Personal User Storage is not part of the SandBlast Mobile solution. References: SandBlast Mobile Architecture