Weekend Sale - Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: sntaclus

examout.co

Location technology (RTLS) can use which of the following methods?(Choose all that apply.)

Response:

A.

Sound

B.

802.11-capable laptops

C.

Active RFID

D.

Infrared

E.

UHV

F.

UWB

G.

Passive RFID

A museum wants to offer Wi-Fi to its visitors. One of their requirements is to have the APs blend into the design of the museum. What should you do to meet this requirement?

Response:

A.

Use a plastic cover that could blend in with the environment

B.

Lock the AP inside of a metal box

C.

Place the APs in between walls and I-beams

D.

Use an 802.11b AP, so it looks old enough to be in a museum

Four buildings are located in a square orientation to each other. Fisch Stix Food Company is requesting a PtMP link between the buildings. On the building with the root bridge link, what type of antenna is the best choice?

Response:

A.

Vertically polarized omni

B.

60° yagi

C.

Parabolic dish

D.

100° sector

E.

Horizontally polarized omni

What kind of antenna results in a nearly circular pattern on the azimuth chart but a very flat donut shape on the elevation chart?

A.

High gain omni-directional

B.

20 degree vertical yagi

C.

120 degree horizontal sector

D.

60 degree horizontal patch

What is the purpose of DHCP Option 43, and how is it used with WLANs?

A.

It provides clients with a temporary IP address on a restricted VLAN until 802.1X authentication is completed. Then the client receives its

long-term IP address.

B.

It provides IP address bindings for specific network nodes that require long-term IP address assignments. WLAN controllers are configured

to use Option 43 to receive long-term IP address leases that are centrally managed with DHCP.

C.

It supports vendor-specific IP address attributes for node discovery purposes. APs use Option 43 with vendor class identifiers to obtain the

IP address of a centralized WLAN controller.

D.

It integrates a DHCP server with AAA servers and user databases to dynamically assign IP addresses to client devices. During 802.1X, the

AAA server uses

What strategy can be used to ensure efficient cell overlap for VoIP site surveys?

Response:

A.

Measure the percentage of cell overlap using the cell overlap feature in the site survey software.

B.

Increase the output power of the radio in all APs.

C.

Install higher gain antennas in the APs.

D.

Ensure at least two APs can be seen with appropriate signal strengths from each location.

After successfully deploying and validating a WLAN intra structure, who should be trained for a better understanding and management of the solution? (Choose the single best answer)

A.

Support staff and end-users

B.

CEOs and other executives

C.

Guests and CEOs

D.

WLAN designer and WLAN implemented

NicoCo is building a new facility and would like to install a WLAN for primary connectivity of all clients. The requirements are dual-spectrum 802.11n supporting voice and location tracking.

What type of pre-deployment survey should be performed?

Response:

A.

Passive, using optimized channels

B.

Active, using a voice handset

C.

Active, using a lowest common denominator client

D.

Predictive

E.

Passive, all channels

Even when a full pre-design site survey is not performed, what is always recommended to be performed within the deployment areas?

A.

A spectrum analysis walkthrough

B.

An AP-on-a-stick survey of 37% of the facility as this amount provides all of the statistical information required for good design

C.

A scan m the 5 GHz band looking for common loT interferes

D.

A scan in the Sub-i GHz bands to determine If sideband interference will impact 2 4 GHz operations

You are using site software design features. You have imported a floor plan, but the simulated RF coverage is nowhere close to the real RF coverage you see with a walkabout.

Given that the simulation is significantly different, when step was likely missed when using the software?

Response:

A.

Conversion to DWG

B.

Conversion to PNG

C.

Adding extra APs to simulate interference

D.

Calibration