You want to restore a configuration that was saved previously from the FTP server using this command:
copy ftp://anonymous:pass@10.255.1.89/VDX25-1-389.cfg running-config
The system responds with the error:
"Error while retrieving file over ftp. Please check the host IP address, user/password, and the permission and space left on the remote directory."
What is the problem?
You are providing cloud-based virtual desktops to businesses from your data center. Each business needs to be completely segmented from each other; however, to keep costs down, you decide to use a single DHCP and DNS server with the least amount of configuration.
Which three features must be configured in the Brocade VCS Fabric? (Choose three.)
In NOS 3.x and later, how many maximum ISLs can exist in a trunk group between a Brocade VDX 8710 and a Brocade Mi10K in a Brocade VCS Fabric?
Referring to the exhibit, you are experiencing latency issues on interface Te 27/0/60.
switch# show interface tengigabitethernet 27/0/60
TenGigabitEthernet 27/0/60 is up, line protocol is up (connected)
Hardware is Ethernet, address is 0005.3367.26d8
Current address is 0005.3367.26d8
Pluggable media present
Interface index (ifindex) is 283874428169
MTU 2500 bytes
LineSpeed Actual : 10000 Mbit
LineSpeed Configured : Auto, Duplex: Full
Flowcontrol rx: off, tx: off
Last clearing of show interface counters: 22:07:59
Queueing strategy: fifo
Receive Statistics:
15254 packets, 1395269 bytes
Unicasts: 10641, Multicasts: 2637, Broadcasts: 1976
64-byte pkts: 10874, Over 64-byte pkts: 3294, Over 127-byte pkts: 117
Over 255-byte pkts: 969, Over 511-byte pkts: 0, Over 1023-byte pkts: 0
Over 1518-byte pkts(Jumbo): 0
Runts: 0, Jabbers: 0, CRC: 1128350, Overruns: 0
Errors: 1128350, Discards: 0
Transmit Statistics:
12633 packets, 1155963 bytes
Unicasts: 18, Multicasts: 12615, Broadcasts: 0
Underruns: 0
Errors: 0, Discards: 0
Rate info (interval 299 seconds):
Input 0.000128 Mbits/sec, 0 packets/sec, 0.00% of line-rate
Output 0.000000 Mbits/sec, 0 packets/sec, 0.00% of line-rate
Time since last interface status change: 0d00h40m
What are two reasons for the problem? (Choose two.)
Which two port profile attributes would be assigned before applying the port profile to an interface? (Choose two.)
You are not receiving any encrypted SNMP notify messages from your Brocade VCS Fabric.
Which two actions must be configured in the fabric? (Choose two.)
After connecting a new server to your four-switch Brocade VCS Fabric, you notice that all the switches have learned the new server's MAC address.
Which VCS feature is responsible for this behavior?
Which two statements are true regarding Access Gateway mode on the Brocade VDX 6730? (Choose two.)
You are troubleshooting an FCoE login problem in your environment. The port shown in the exhibit has not been able to log into the fabric. The default FCoE fabric map in your environment has not been changed.
Interface TenGigabitEthernet 3/0/4
Mode PFC
DCBX enabled for PFC negotiation
TX 0 frames
TX TX RX RX Output Paused
CoS Admin Oper Admin Oper 512 BitTimes
---------------------------------------
0 Off Off Off Off 0
1 Off Off Off Off 0
2 Off Off Off Off 0
3 On Off On Off 0
4 Off Off Off Off 0
5 Off Off Off Off 0
6 Off Off Off Off 0
7 Off Off Off Off 0
sw0(conf-if-te-3/0/1-24)# do show lldp neighbors interface ten 3/0/4 detail
Neighbors for Interface Te 3/0/4
---
DCBX TLVs
===========
Version : CEE
DCBX Ctrl OperVersion: 0 MaxVersion: 0 SeqNo: 4 AckNo: 6
DCBX ETS OperVersion: 0 MaxVersion: 0 Enabled: 1 Willing: 0 Error: 1
Enhanced Transmission Selection (ETS)
Priority-Group ID Map:
Priority : 0 1 2 3 4 5 6 7
Group ID : 0 0 0 0 1 0 0 0
Group ID Bandwidth Map:
Group ID : 0 1 2 3 4 5 6 7
Percentage: 50 50 0 0 0 0 0 0
Number of Traffic Classes supported: 2
DCBX PFC OperVersion: 0 MaxVersion: 0 Enabled: 0 Willing: 0 Error: 1
Priority-based Flow Control (PFC)
Enabled Priorities: 3
Number of Traffic Class PFC supported: 8
FCoE App OperVersion: 0 MaxVersion: 0 Enabled: 1 Willing: 0 Error: 0
FCoE Application Protocol
User Priorities: 4
What are two causes of the problem? (Choose two.)
A customer has configured sFlow on a four node VCS cluster which includes one Brocade VDX 8770 and three VDX 6740T-1G switches. The customer sees sFlow samples from all the interfaces on the VDX 8770 but is not seeing sFlow samples from the 1 GbE interfaces on the VDX 6740T-1G switches.
Which statement is correct?
